Loading... Please wait...

Blog

Enhance customer satisfying rate of our 5C Collet Chucks

Posted by


We've noticed the high demand of our 5C Collet Chucks Inspection. To help customers easy access the inspection T.I.R, we've required our MFG inspect every piece of the chuck. We believe our buyers will be more satisfied with our 5C Collet Chucks.

The technicians of the MFG will inspect the 5C collet chucks one by one. They will create a report for each chuck. So in the future, each of our 5C collet chucks will have a unique serial no. on its side.


(The photo shows the sample chuck has a unique serial number within the red circle. The chuck you buy won't have the same serial no as the pic above.)

The unique number will also be printed on the report created by the MFG and packed into the parcel of the chuck. So it means each chuck has a unique inspection detailed report. The Inspection Sheet of each report has a different result. Only the chucks with acceptable runout and accuracy will be shipped to our warehouse.


(From the photo above, you can see a serial number and a result are on the Inspection Sheet of the report. The serial no. is the same as the one on the sample chuck. The result shows the sample D1-6 chuck has an acceptable accuracy. )

Maybe you will get a different result by your own method which may make you skeptical about the chuck. However, the MFG inspect it very strictly. Everything is so accurate. The MFG also export the chucks to the very large enterprises. All of them are working perfect.


How to exchange the inserts of Accusize tool holders

Sample: 3/4"x4-1/2" MWLN R-12-4C Toolholder, RH, #2316-0008Loose the upper bigger nut screw. (Counter clockwise) After the upper bigger screw looses, start to loosen the small screw inside the insert. All the screws need counter clockwise to loosen, while the clockwise will made the screws tighter.The screw inside the insert does not have to be too tight; [...]

Read More »

CAT APU Drill Chuck

Mount APU Drill Chuck Holder firmly according to" HOW TO MOUNT" in this manual. Otherwise the holder might be loosened, which may eventually result in serious bodily injuries or accidents for user.Check and confirm the drill bit is clamped firmly by the chuck before starting operation. Improper clamping of the drill bits will cause its abnormal [...]

Read More »

Keyless Drill Chuck Manual

CautionMount the chuck firmly according to "How to mount" in this manual. Otherwise, the chuck might be loosened, which may eventually result in serious bodily injuries or accidents.Check and confirm that the tool is clamped firmly by the three jaws before starting operation. Improper clamping of the tool will cause its abnormal run out, breakage and/or detaching, which may [...]

Read More »

ER Collet Chuck

Mount ER collet chuck firmly according to "HOW TO MOUNT" in this manual. Otherwise, the tool holder might be loosened, which may eventually result in serious bodily injuries or accidents for user.Check and confirm the tool is clamped firmly by the tool holder before starting operation. Improper clamping of the tool will cause its abnormal run out, breakage or detaching [...]

Read More »

ER Collets and Nuts - Mounting Instructions

How to Set Up and Take Out ER ColletsThe image above details how to mount and change ER collets and nuts. The same image is also available on product pages for 0223-0974, 0223-0984, and ER Collet Systems.

Read More »

Everything about Standard Design Micrometers

Standard Design Micrometers For all of our standard micrometers Fasten micrometer in a clamp, then test by putting a set of gauge blocks between two measuring faces. They are the first-class gauge blocks as following: 52..15; 7.7; 10.3; 12.9; 15.0; 17.6; 20.2; 22.8 and 25mm. In above ten positions, get ten error data between micrometer reading and actual distance [...]

Read More »

Maintenance For Electronic Micrometers

Maintenance For Electronic Digital Outside Micrometers(5-Key Electronic Digital Outside Micrometers)  Display “E 1” on LCD Measuring value over display range. Repairing: Reset the origin or convert to relative measuring mode. Display “E [...]

Read More »

Recommended cutting speed and feed for our end mills

Recommended cutting speed and feed for Accusize Industrial end mills 6800 series, M42 ( HSS + 8% Cobalt ) Finishing CNC end mill, 4 flute, TiALN Coated,1002, 1102, and 1104 series M42 ( HSS + 8% Cobalt ) CNC Roughing end mills, TiALN Coated

Read More »

Products On Sale


 

What's News

newsletter

Copyright 2017 Accusize Industrial Tools. All Rights Reserved.
Sitemap | BigCommerce Premium Themes by PSDCenter